Keyence - trimatec GmbH - control and regulation software for automated plants

Accessories

In this section you will find option accessories to complement KEYENCE CORPORATION products.

Note: This product area can only be accessed via the direct link or QR code just used and cannot be found via the navigation menu!

Protective covers

All protective covers are supplied including the required holder
Material holder: anodised aluminium
Protective glass variant Makrolon: thickness 6mm
Schutzglas-Variante Laser: Quarzglasplanoptik, Dicke 6mm, Transmission @900-1100 nm <5%, Transmission @400-800nm >90%
As spare parts, the protective glasses can also be ordered individually (laser protection) or in a pack of 10 (Makrolon).

Brackets for on-site mounting of the Keyence sensor are not included in our scope of delivery

Keyence product	Figure Accessories	Available variants
		Coated Quartz glass (Laser protection)	Makrolon glass (Rugged Use)
SR-750 SR-750HA SR-751	Protective glass
SR752	Protective glass
SR-1000 SR-1000W	Protective glass
SR-1000 SR-1000W	Protective glass angled
SR-2000 SR-2000W	Protective glass
IV2	Protective glass
IX	Protective glass
LR-TB5000 LR-TB5000C LR-TB5000CL	Protective glass

Protective housing SR-1000

Protective housing for installation of a code reader Keyence SR-1000(W)
Material: Stainless steel (suitable for food environment)
Protection factor IP65
Viewing element made of quartz glass with lotus effect coating "T-Rauri Superphob
Separable zinc die-cast cable gland. 2-fold sealing insert for installation of Keyence standard cables.
Dehumidification element Gore® Protective-Vent
Enclosure mounting position any
Mechanical connection on customer side: Drilling pattern on rear side can be produced specifically according to customer requirements without surcharge

Keyence product	Figure Accessories
SR-1000 SR-1000W

Protective housing SR-2000

Protective housing for installation of a code reader Keyence SR-2000(W)
Material: Anodised aluminium
Protection factor IP65
Viewing element: acrylic glass
Separable cable gland made of die-cast zinc. 3-fold sealing insert for installation of Keyence standard cables.
Heating cabling prepared ready for connection
Dehumidification element Gore® Protective-Vent
Enclosure mounting position any

Optional: heating element for use down to -15°C
Optional: vibration damping (e.g. for use in industrial trucks)
Optional: Quartz glass with lotus effect coating "T-Rauri Superphob

Housing installation position vertical (only with heating variant)

Detailed device page for users

Keyence product	Figure Accessories
SR-2000 SR-2000W

Protective housing SR-5000

Protective housing for installation of a code reader Keyence SR-5000W
Material: Anodised aluminium
Protection factor IP65
Viewing element: quartz glass with lotus effect coating "T-Rauri Superphob
Separable cable gland made of die-cast zinc. 3-fold sealing insert for installation of Keyence standard cables.
Heating cabling prepared ready for connection
Dehumidification element Gore® Protective-Vent
Enclosure mounting position any

Housing installation position vertical (only with heating variant)

Optional: heating element for use down to -20°C

Keyence product	Figure Accessories
SR-5000
SR-5000W

Active cables

Y-cable for connecting a Keyence SR-1000/2000 ID code reader to a customer serial communication port as well as to the customer mains supply

Input side1: Round plug "Keyence" 12-pole in housing, cable length 2m / 5m / 10m
Input side2: EURO plug switching power supply primary 100...240VAC / 50...60Hz, secondary 24VDC/1A, total cable length 2.5m (cable in two parts), socket/plug separation integrated in cable
Output side: D-Sub socket, 9-pin, Encitech TRI-M housing, output straight or lateral 90°, connection to serial interface of the PC.
Cable-connector transitions each shrink-wrapped or sealed, unused single wires shrink-wrapped
Cable type PUR, shielded, drag chain suitable, NFPA79 compliant, 0.34mm2
Ready for connection

Keyence product	Figure Accessories
SR-1000(W) SR-2000(W)

Passive cables

Supply cable for connecting a Keyence SR-1000/2000 ID code reader to a standard-compliant bus distributor

Input side: Round plug M12, 5-pin, A-coded, output straight, IP69K
Output side: Round plug "Keyence" 12-pole in housing
Cable-connector transitions each shrink-wrapped or sealed, unused single wires shrink-wrapped
Cable type PUR, shielded, drag chain suitable, NFPA79 compliant, 0.34mm2
Ready for connection

Keyence product	Figure Accessories
SR-1000(W) SR-2000(W)

If you have any questions about the products, please do not hesitate to contact us by phone at +49 841 885579-0 or by email at info@trimatec.com at your disposal!